Polarized Light Source and Component Testing Solutions

Testing of polarization performance, optical power, spectrum and end face quality for polarization-preserving light sources and laser components.

Plan Introduction
Advantages of the plan
Related Products

Scheme Introduction

Polarized light sources and components are widely used in optical systems where there are requirements for polarization direction and output stability. Dimension Technology, focusing on research and development verification as well as production inspection, combines polarization extinction ratio testers, optical power meters, spectral analyzers, optical switches, and end face detection and cleaning equipment to cover optical performance measurement and connection port quality inspection, helping users build a complete testing system.


Polarized Light Source and Component Testing Solutions.png

                                                                                                        Overview of Polarization Light Source and Component Testing System


Polarization Light Source and Component Testing Circuit Diagram


偏振光源及组件测试线路图.png



Polarization extinction ratio and polarization angle measurement

Polarization Extinction Ratio tester

For polarization-preserving light sources and laser components, measure the polarization extinction ratio (PER) and polarization angle of the output light to evaluate the polarization retention capability and the consistency of the output direction. The PER polarization extinction ratio tester integrates polarization extinction ratio, polarization angle, and optical power measurement functions, covering the communication band of 1260–1650 nm. It can be used for R&D debugging, assembly verification, and finished product inspection. During measurement, the tail fiber state should be fixed and the connection conditions should be kept consistent. For high PER devices, it is recommended to directly connect the tested device to the PER instrument; when using an optical switch for multi-channel testing, it is necessary to first verify the impact of the switching link on the measurement results.

PER 偏振消光比测试仪.png

                                                        Polarization Extinction Ratio tester


Output power and power stability test

Optical Power Meter

Measures the output optical power of the tested component and observes the change of power over time through continuous collection, which is used to evaluate the output level and stability. The OPM optical power meter provides various module and channel configurations, and can be combined with the test platform to build a single-channel or multi-channel power measurement system.

2026110709487014.png

                                         Optical Power Meter


Spectral performance test

OSA spectral analyzer

Measure the central wavelength, spectral width and edge-mode suppression ratio to evaluate the spectral characteristics of the laser output. Select the spectral analyzer according to the wavelength range, spectral width and edge-mode suppression ratio requirements of the measured object, and correlate the spectral results with the polarization and power test results to form a complete performance record.


Multi-channel optical path switching

Optical Switch

Use the optical switch to connect different measured channels or testing instruments to reduce repeated plugging and unplugging and facilitate the construction of a multi-channel testing process. OSW can be configured according to the number of channels and interface form; for applications requiring input light monitoring, a testing system can be built in combination with a power monitoring scheme. The PER measurement link needs to be verified separately to avoid the change of the polarization state when switching the link and affecting the results.

2026110709529272.png

                                                                                             Optical Switch


Optical fiber end face defect detection

FastCheck Pro Fully Automatic Fiber Endface Inspector

EasyGet WiFi  Wireless Fiber Endface Microscope

MT SCOPE   Fiber Endface Microscope

Check for contamination, scratches and other defects on the connection end face, reducing interference to power and polarization measurements caused by the connection status. FastCheck Pro supports automatic centering, focusing, exposure and measurement, suitable for bench-top detection and integration with automation; EasyGet WiFi supports wireless transmission, automatic analysis and report output; MT SCOPE comes with a touch screen and can independently complete on-site detection and determination. Specific interfaces require corresponding adapters.

2026110709504671.png


                                                               Fiber Endface Inspector


End face cleaning

Offsoon Pro Fiber Endface Cleaning Machine

It adopts a non-contact cleaning method combining cleaning solution and dust-free gas to remove oil stains and adhered contaminants on the connection end face. It is recommended to confirm the end face condition following the "inspection - cleaning - re-inspection" process, and re-apply the cleaning process only after the re-inspection is qualified; the cleaning head and process are configured according to the interface structure.

2026110709503381.png

                                              Offsoon Pro Fiber Endface Cleaning Machine



Advantages of the plan

· Covers multiple key quality indicators

Incorporate polarization extinction ratio, polarization angle, output power, power stability and spectral characteristics into the same testing scheme, supporting the research and development verification and production inspection of polarization light sources and components.

· Configure the testing system according to the tested item

Select instruments and fixtures based on interface form, number of test channels and inspection items, supporting the expansion from single instrument measurement to multi-instrument combined testing.

· Take into account both optical performance and end face quality

Incorporate end face detection, cleaning and re-inspection into the testing process, reducing measurement fluctuations caused by contamination and repeated plugging and unplugging, and facilitating the identification of connection and component issues.

· Facilitate the connection of automated testing processes

Through modular platforms and optical path switching configurations, organize multi-channel testing; combined with instrument communication capabilities and upper computer software, it can further achieve task control, result association and report output.


Product List


Product Name

Main Application

Polarization Attenuation Ratio Tester

Polarization extinction ratio, polarization angle and optical power measurement

Optical Power Meter

Output optical power and power stability test

OSA Spectral Analyzer

Center wavelength, spectral width and edge-mode suppression ratio test

Optical Switch

Multi-channel optical path switching and test link configuration

OMEGA Testing Platform

Assemble power meters, optical switches and other modules to build a combined test system

FastCheck Pro Fully Automatic Fiber Endface Inspector

Desktop end face inspection and automation equipment integration

EasyGet WiFi Wireless Fiber Endface Microscope

Wireless end face inspection, result analysis and report output

MT SCOPE Fiber Endface Microscope

Independent operation of on-site end face detection and determination

Offsoon Pro Fiber Endface Cleaning Machine

End face contamination cleaning, combined with end inspection equipment to complete re-inspection



















The equipment configuration is determined based on the wavelength range, output power, interface form and test accuracy requirements of the tested component.


Easily access services and support from Dimension
Want help or have questions?