

SmartCheck FV
Full-Field Endface Inspector
Dual-mode Imaging | Fully Automatic Inspection | Efficient Production Line Deployment
With the continuous development of CPO (Co-Packaged Optics), high-density optical connectors and high-speed optical modules, endface inspection requires both full coverage and high resolution. For structures such as multi-fiber arrays and FA fiber arrays, balancing overall ferrule cleanliness inspection and fine defect detection on individual fiber cores has become a critical requirement for R&D and mass production testing.
Main Advantage
· Dual-mode Imaging: Large FOV for overview, Small FOV for details
· LFOV: 6.4 × 2.5 mm, captures the entire ferrule endface in one shot
· SFOV: 0.6 μm optical resolution for detailed inspection of single fiber cores
· Automated Inspection: Integrated focusing, exposure, measurement and pass/fail judgment
· Compact Design: Suitable for bench-top stations and production line integration
Main Application
· CPO co-packaged optical device endface inspection
· FA fiber array production and quality inspection
· High-density optical connector endface inspection
· Laboratory R&D and endface analysis
Large Field of View, Capture the Entire Ferrule in One Shot
In traditional detection methods, if the field of view is insufficient, it is necessary to frequently switch observation positions, making it difficult to quickly grasp the overall situation of the entire chip end face. The LFOV wide field-of-view mode of SmartCheck FV covers a range of 6.4 × 2.5 mm, enabling the presentation of the entire chip end face in a single scan, providing support for the cleanliness inspection of multi-core arrays.
At the same time, the equipment can combine the PIN hole measurement function to check the relevant features of the guide holes based on the overall imaging. For scenarios where end face determination according to standards such as IEC 61300-3-35:2022 is required, detection rules can be set according to the tested interface and applicable requirements.

Small Field of View, Precisely Capture Subtle Defects
Full ferrule inspection calls for a large field of view, while critical regions of individual fiber cores demand finer observation. The SFOV mode of SmartCheck FV adopts 4× high-resolution imaging to deliver an optical resolution of 0.6 μm for examining subtle features on single fiber cores and their surroundings.
It automatically locates fiber core regions and outputs results based on applicable zoning criteria, enabling inspectors to assess endface conditions efficiently and balancing global overview with local details.

FA Component Inspection for Precision Packaging Scenarios
With the advancement of silicon photonics and CPO packaging applications, endface inspection for FA fiber arrays involves multi-fiber alignment, visible defect detection, and condition verification before and after assembly. Designed for FA component endface inspection, SmartCheck FV supports automated measurement and judgment workflows to provide evidence for production and quality verification.
For FA devices of different configurations and other high-density connectors, adaptation schemes and specific inspection items can be defined according to actual samples, field-of-view coverage and inspection standards.

Fully Automatic Inspection to Boost Mass Production Takt Time
In mass production scenarios, endface inspection must balance ease of operation, test takt time and result consistency. According to product documentation, SmartCheck FV completes full-endface MT inspection within ≤5 seconds, with automatic focusing, exposure and measurement sequences. Actual takt time depends on sample type, inspection recipe and production setup.
The instrument supports communication interfaces such as TCP and ini for data integration and centralized management, enabling integration into automated inspection stations and production line systems.

ntelligent Software, One-click Inspection Result Output
SmartCheck FV allows configuration of inspection items and acceptance criteria to meet actual testing requirements. Once the operator starts inspection, the system sequentially performs full ferrule cleanliness check, zoned evaluation for each fiber core and Pass/Fail result output, eliminating manual switching and subjective judgment.
The system supports inspection report generation, data export and traceability, retaining records for process analysis, quality management and subsequent troubleshooting.

Specifications

Choose SmartCheck FV and achieve both full coverage and fine detail in endface inspection!
For more product details, stay tuned to the new release updates of SmartCheck FV!
![]()

Scan the QR code below to follow us

More news recommendations
-
Get Pitch New Launch: Built for 800G/1.6T High-Speed Optical Interconnects!
2026.10.16
-
SmartCheck FV New Launch: Full Field of View for Comprehensive Inspection, Precisely Capture Tiny Defects!
2026.09.30
-
Industry 4.0 Innovation – Fully Automatic Optical Component Cleaning & Inspection System Solution! Grand Debut! High Efficiency & Reliability
2025.07.03
-
AutoGet MT: A High-Efficiency Inspection Tool Built for 1.6T / 800G Optical Modules and Data Centers! Revealing Hidden Defects on Fiber Endfaces!
2025.06.18
-
Full-Core View | FastCheck MT Benchtop Fiber Endface Inspector, Empowering New Standards for High-Precision Inspection
2025.03.21